The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
Were you hunting for guidance concerning Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a bathtub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old tub is conveniently accessible, the task can relocate speedily; if you have to open a wall surface to eliminate the old bathtub as well as position the new bath tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also set in the new one. See to it you have qualified on your own for the work as well as are comfortable trying it. As opposed to working with a specialist to take over a halfway-completed job, it is better to take into consideration employing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This write-up will assist you mount a new bathtub in your shower room if you have actually currently purchased a brand-new tub and do not require to change the setup of your previous supply of water pipelines.
Your tools as well as product checklist should consist of the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub until the level checks out degree.
To set up faucets, fit all-time low of the furthest flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the water system and also check all joints and also brand-new pipework for leaks and tighten them if needed. Fill up the bath tub as well as likewise examine the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bath tub has been utilized at the very least once as this will certainly settle it right into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a stiff seal, causing the water to pass through the wall surface between the bath and the tiling, bring about issues with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the search engines. If you appreciated our blog entry if you please don't forget to pass it around. We enjoy reading our article about Installing A Bathtub.
We're here 24/7, call! Report this page